







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Home Additions & ADU: The Enterprise Owner’s Guide
In Enterprise, a Schluter-based addition or ADU project usually runs $45,000 – $130,000 for the build itself, with Schluter waterproofing and edge-trim assemblies accounting for a small slice of that total but a large share of the failures we’re called back to fix. If a Schluter membrane, trim profile, or bonded flange has failed, we replace the part and correct the installation that killed it. Most repairs are scheduled within a few business days, not same-day.

Owners here usually discover the problem the same way. A shower pan in a new ADU starts weeping at the curb. A Kerdi-Band seam lifts behind a tile in the addition’s bathroom. Or the Ditra underlayment under the laundry-room tile in a garage conversion sounds hollow when you walk it. By the time you see water staining on the ceiling below, the failure has been working quietly for months.
Key Takeaways
- Schluter failures in Enterprise are almost always installation failures, not product failures.
- Replacement parts run modest; the labor to expose and correct them runs the bill.
- Written price before work starts, every project, every time.
- 365-Day Done Right Promise covers the installation for a full year from completion.
Which Schluter Models This Applies To

Schluter builds dozens of profiles, and the part number matters. Kerdi-Band comes in 5″ and 7-1/4″ widths with specific bond-fleece webbing on both faces. Ditra is sold in 3′-3″ and 1-meter rolls, and Ditra-Heat is a different assembly entirely with the heating cable set into the mat. Kerdi-Fix is a sealant, not an adhesive substitute, and using it in place of thin-set at a shower floor seam is one of the most common mistakes we correct in Enterprise.
Identify your part by the printing on the roll or sheet, not by the color. The Kerdi orange and the Ditra orange are close enough to confuse under a work light. Check the roll width and the printed product name together. If the label is gone, measure the band width and thickness and we’ll match it against the current spec sheet.
The OEM-versus-aftermarket call depends on the part. For Kerdi-Band and Kerdi-Fix, buy the Schluter part. The bond-fleece formulation and the sealant cure chemistry are the whole reason the system holds water, and a generic band at the same width won’t carry the same approval. For something like a PVC edge profile where the function is simply trim, a quality aftermarket equivalent at the same dimensions does the job. We’re an independent service provider, not affiliated with Schluter, so we tell you plainly which is which.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Home Additions & ADU Is Failing
- Hollow tile over Ditra. The thinset under the mat never fully bonded, usually because the fleece was contaminated or the mix was too stiff for a 3/16″ trowel. Tap a few tiles in the ADU bath floor and listen for the dull echo.
- Lifting Kerdi-Band at a seam. The band edge peels up because the thin-set was allowed to skin over before the band was pressed, or the 2″ overlap wasn’t honored. Once it lifts, water tracks behind the tile.
- Grout haze or efflorescence at the shower curb. Water is getting past the waterproofing and pulling minerals to the surface. In Enterprise’s dry heat, that wicking shows up faster than it does in humid climates, because the interior stays cool and dry while the hidden moisture pushes out.
- A dark stain on an exterior wall of the addition. Tile set over Kerdi on an exterior wall without the correct vapor handling traps moisture. You’ll see a stain line before you see soft sheathing.
- Loose edge trim at the transition. A Schluter strip that’s pulling from the wall means the fastener or adhesive failed, often because the profile was installed over a painted surface instead of back to substrate.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For a single failed detail inside an addition or ADU bathroom, expect $850 – $2,400 installed. That covers demo of the affected tile, replacement of the Schluter band or membrane with the correct OEM part, new thin-set, tile re-set, grout, and caulk. A failed shower pan rebuild with new Kerdi and drain flange runs $4,500 – $12,000. Full replacement of a shower assembly in a new build or addition lands in the $4,000 – $9,000 range depending on tile and size.
What drives the range: how much finished surface has to come out to reach the failure, whether the drain flange is salvageable, and the tile itself. A $60 roll of Kerdi-Band is cheap. Getting to it is not. We give you a written line-item price before any work starts, parts and labor shown separately, and the 365-Day Done Right Promise covers the installation for 365 days from the completion date. If it fails inside that window, we return at no charge.
DIY or Call Us?
You can safely check a few things yourself. Press on a suspicious seam with your thumb and see if it’s still bonded. Look at the drain flange and see whether the membrane laps over it. Measure your band width and snap the label on the roll. Those checks cost nothing and tell you a lot.
Where DIY goes wrong: re-band a shower pan without pulling the existing tile back to sound thin-set and you’re just trapping water behind a new seal. Cut out Ditra and re-set it without the right trowel and mix, and the new section sounds hollow in a month. We’d rather do it once.
Call Mason Remodeling Enterprise at (844) 797-6157 for a free assessment. A live person answers every call, 24 hours a day.
FAQs

How long does a Schluter waterproofing system last in Enterprise? A correctly installed Kerdi or Ditra assembly lasts decades. The product isn’t the lifespan limiter. Installation detail is. In Southern Nevada, the dry air and big temperature swings between a hot exterior wall and a cooled interior stress the vapor path, so exterior walls of an addition need proper handling.
Can it be repaired instead of replaced? Yes, in most cases. A single lifted seam or a failed curb can be repaired without rebuilding the whole shower, provided the surrounding membrane is still bonded. Call (844) 797-6157 and we’ll tell you honestly which one you’re facing.
How long does the swap take? A single seam repair is a one-day job. A shower pan rebuild runs three to five days to allow the thin-set and grout to cure properly. Rushing that timeline is how these fail.
How do you source the Schluter part? We buy from Schluter-authorized distributors and match your existing assembly’s width, thickness, and fleece specification. We don’t carry parts on a truck. We order the exact profile and confirm the part number with you before install. Call (844) 797-6157 to schedule a free estimate.
Call Mason Remodeling Enterprise at (844) 797-6157 for your free estimate. Every crew member is identity-verified under The Threshold Standard, and you’ll receive their name and photo before they arrive.
Written by the team at Mason Remodeling Enterprise, serving Enterprise and nearby areas.












