







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Bathroom Remodeling in Enterprise, NV: The Owner’s Parts and Replacement Guide
We install CGI-compatible bathroom remodeling in Enterprise, and a full bathroom remodel typically runs $9,000 – $28,000 installed, with smaller baths at $5,000 – $12,000. While most projects are scheduled a few days to a couple of weeks out, we encourage you to call early, since fixture lead times vary. Mason Remodeling Enterprise is an independent service provider and is not affiliated with CGI; we work with CGI products on a service and installation basis.

Owners usually find out something is wrong in one of two ways. Sometimes a shower valve handle turns but the water temperature won’t hold; other times a vanity top or shower pan that looked fine at move-in starts showing hairline cracks or soft spots. In Enterprise’s dry desert climate, rapid temperature swings between day and night put extra stress on caulk lines and grout, so small failures show up faster here than in milder regions. This page gives you honest pricing, what to check, and when it’s time to call us at (844) 797-6157.
Key Takeaways
- Full CGI-compatible bathroom remodels in Enterprise run $9,000 – $28,000 installed.
- Small bathroom remodels range $5,000 – $12,000.
- We confirm the correct CGI-compatible parts before ordering, then install and back the work with a written guarantee.
- Call (844) 797-6157 for a free written estimate before any work starts.
Which CGI Models This Applies To

CGI manufactures a wide range of bathroom fixtures, from shower valves and trim kits to vanity tops, faucets, and shower pans. The part you need depends on your specific CGI series, so the single most useful thing you can do before calling is find the model or series number. On CGI shower valves, that label is usually on the rough-in valve body behind the trim plate, or printed on the cartridge itself. On vanity tops and shower pans, check the underside or the original installation paperwork. Grab a photo of the label if you can get one without taking anything apart.
Once we know the series, we can talk about OEM versus quality aftermarket options. OEM CGI parts fit exactly and match the finish you already have. Quality aftermarket equivalents often cost less and perform well, but the fit can vary by a millimeter or two on trim pieces, and finish matches aren’t always perfect. We’ll tell you honestly which route makes sense for your model and budget. The same applies if you’re also replacing KraftMaid cabinetry, Cambria or Silestone surfaces elsewhere in the bath. Our technicians have up to 22 years of experience matching parts to fixtures, so we’d rather spend five minutes confirming the model than order the wrong valve and delay your project.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Bathroom Remodeling Is Failing
Here’s what failing CGI bathroom components usually look like, and what’s causing each one:
- Shower valve won’t hold temperature. The internal cartridge has worn or scaled up, which is common in Enterprise’s hard water. You turn the handle and the water runs hot, then cold, then hot again.
- Water dripping from the showerhead after shutoff. A worn valve seat or cartridge lets water past the seal. Left alone, that slow drip can stain tile and waste water.
- Hairline cracks or soft spots in the shower pan. The pan material has flexed or the waterproofing beneath it has failed. In Enterprise, the dry climate and daily sun exposure through windows can speed up cracking in some pan materials.
- Loose or wobbling vanity top. The adhesive or mounting has given way, or the cabinet top has swelled from a slow leak. A wobbly top is a sign to check for water damage underneath.
- Caulk or grout failing at joints. Constant expansion and contraction, plus dry air, breaks the seal at corners and where tile meets the pan. That’s the first place water gets behind the wall.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included in Enterprise

For a full CGI-compatible bathroom remodel in Enterprise, expect $9,000 – $28,000. A small bathroom remodel runs $5,000 – $12,000. A walk-in shower installation is $4,500 – $12,000, a tub-to-shower conversion is $3,500 – $10,000, and a shower replacement alone is $3,000 – $8,500. If you’re only replacing a vanity, that’s $800 – $3,000.
What drives the range: the CGI series and finish you choose, whether walls or subfloor need repair behind the fixture, and whether you’re changing the layout. We don’t hide parts costs in a lump sum. Your written quote breaks out the fixture, the labor, and any repair work, so you can see exactly what you’re paying for before we start. Every project is backed by our 365-Day Done Right Promise: if the work isn’t right within a year of completion, we make it right at no cost to you. Estimates are free, and the price is in writing before any tool comes out.
DIY or Call Us?
Some things you can safely check yourself. You can find the model number, take photos of the label, look for visible cracks or soft spots, and test whether the valve handle turns smoothly. You can also check for water staining under the vanity or around the shower base, which tells you whether there’s a leak worth investigating.
Where DIY goes wrong: anything involving the shower valve body, the waterproofing layer under tile, or the supply lines behind the wall. Opening a valve body means shutting off water to the house, and a mistake there can flood a bathroom in minutes. Waterproofing done wrong doesn’t show up until mold does, months later. That’s not a scare tactic; it’s just how the work behaves. If your CGI fixture is failing and you’re not sure how deep the problem goes, call us at (844) 797-6157 and we’ll tell you honestly whether it’s a quick swap or a bigger repair.
FAQs

How long does a CGI bathroom fixture last?
Most CGI shower cartridges last 8 – 15 years depending on water hardness, and in Enterprise’s hard water you’re often closer to the shorter end. Vanity tops and shower pans can last much longer if the waterproofing and seals are maintained. When a fixture starts failing early, it’s usually a seal or install issue rather than the product itself. Call (844) 797-6157 for a free assessment.
Can it be repaired instead of replaced?
Often, yes. A worn cartridge can be swapped without replacing the whole valve, and a loose vanity top can sometimes be re-secured. But if the valve body is cracked or the shower pan is soft, repair isn’t reliable and replacement makes more sense. We’ll tell you which one you’re looking at after we see it. Call us for a free estimate.
How long does the swap take?
A cartridge or trim swap is usually a couple of hours. A shower replacement runs several days, and a full bathroom remodel takes a few weeks depending on scope and fixture lead times. We give you a realistic schedule in your written quote, not a best-case guess. Call (844) 797-6157 to talk through your project.
How do you source the part?
We identify your CGI model first, then source the correct OEM or quality aftermarket part through our supplier network. We don’t carry parts on a truck or keep local stock, so we confirm the model before ordering to avoid return trips. That’s why the photo of the label matters. Call (844) 797-6157 and we’ll walk you through finding it.
Ready to get a written price on your CGI bathroom project in Enterprise? Call Mason Remodeling Enterprise at (844) 797-6157 for a free estimate. A live person answers every call, and we’ll confirm exactly who’s coming, with a name, photo, and ID badge at the door before any work starts.
Written by the team at Mason Remodeling Enterprise, serving Enterprise and nearby areas.












