







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mr-Glass Kitchen Remodeling: The Enterprise Owner’s Guide
We install and service Mr-Glass-compatible kitchen remodeling components in Enterprise, with typical installed kitchen projects running $14,000 – $45,000 depending on scope, layout changes, and material selection. Smaller projects, like a cabinet-only refresh, land closer to $4,000 – $13,000. Because Mr-Glass runs the same core cabinet and surface platforms across its kitchen lines, replacement doors, drawer fronts, and countertop sections can usually be matched to your existing setup rather than requiring a full gut.

Most Enterprise owners discover a failing component the same way: a drawer front that no longer sits flush against the adjacent cabinet, a hinge that sags until the door catches the frame, or a countertop seam that starts showing a dark line after a few summers of desert heat cycling. Sometimes it’s subtler. A soft spot near the sink base that turns out to be swelling cabinet board, or a backsplash tile that pops loose because the original adhesive couldn’t handle the dry seasonal swing. Whatever brought you here, you probably already know the part needs to be replaced, not explained. We’ll help you figure out what you’re actually dealing with and what it costs to fix it properly.
Which Mr-Glass Models This Applies To

Mr-Glass kitchen components show up across their cabinet series, countertop lines, and integrated storage systems, and the exact part you need depends on which generation you have. Doors and drawer fronts vary by hinge pattern and door thickness, typically 3/4-inch or 5/8-inch, so a matching front from a different year won’t sit flush without modification. Countertop sections need the edge profile matched too; a bullnose and a beveled edge don’t blend.
How to identify yours: pull any interior cabinet label or inspection sticker (Mr-Glass, like most major cabinet makers, places a spec sheet inside the door, usually on the hinge-side panel or under the sink base). Note the series name, the cabinet width, and the finish code. If the label is gone, measure the existing door height and width to the nearest 1/16 inch and photograph the hinge mounting plate. Those two pieces of information let us match the part to your exact model instead of guessing.
On the OEM-versus-aftermarket question: for visible surfaces like door fronts and countertop sections, matching OEM is worth the premium because the finish and profile have to line up with everything already installed. For hidden hardware like hinges, drawer slides, and shelf pins, a quality aftermarket equivalent from a reputable supplier performs just as well for less, and we’ll tell you honestly which path makes sense for your situation. We’re an independent service provider, not affiliated with Mr-Glass, so our only interest is getting the right part in your kitchen at a fair price. We also service KraftMaid, Cambria, and Silestone products if your kitchen has a mix of brands.
Key Takeaways
- Match the door thickness, hinge pattern, and finish code before ordering any front or panel.
- OEM matters for visible surfaces; quality aftermarket is fine for hidden hardware.
- We’re independent, so we’ll quote the honest best option, not the one that pays us more.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Mr-Glass Kitchen Remodeling Is Failing
These are the symptoms Enterprise homeowners describe most often, and what’s usually behind each one:
- A cabinet door sags or won’t stay closed. This is almost always a tired hinge or a hinge plate that’s pulled slightly from the cabinet side. In dry high-desert air, screws loosen over time as the wood board shrinks and expands across seasons, so the fix is often a hinge replacement and a fresh mounting point.
- A drawer front sits crooked or rubs the frame. Usually a drawer slide failure or a front that’s separated from the box at one corner. Drawer boxes in Mr-Glass lines are typically dovetailed or doweled, and a corner that’s worked loose can sometimes be re-glued and re-clamped rather than replaced outright.
- A visible dark line along a countertop seam. A seam that’s opening or darkening signals the adhesive joint is failing, often after repeated heat cycling. Left alone, water and crumbs work into the gap and the seam gets worse.
- Soft or swollen cabinet board near the sink. Moisture intrusion from a slow leak or a worn sink caulk line swells the board, and swelling doesn’t reverse. Once cabinet board takes on water, the affected panel usually needs replacement, not repair.
- A backsplash tile pops loose or a grout line cracks. This points to movement or adhesive failure, often traceable to the original install not accounting for the desert’s seasonal expansion. A single popped tile often means a small area needs re-set rather than the whole backsplash.
If more than two or three of these are showing up at once, it’s worth stepping back and looking at the whole kitchen rather than chasing individual failures, because you may be better served by a targeted renovation than by a string of small repairs.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what typical Mr-Glass-compatible kitchen work runs in Enterprise, part and labor together:
| Scope | Installed Price Range |
|---|---|
| Kitchen remodel (full scope) | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation (incl. fronts, boxes, hardware) | $4,000 – $13,000 |
| Countertop installation (incl. seam re-set) | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
What drives the range up: the number of component groups involved, whether the layout is changing, and material tier. What keeps it lower: matching the existing door series and finish instead of changing them, and limiting work to the failing area. Our price is always written before any work starts, so you see exactly where the labor and parts land. Every project is covered by a written guarantee, and if a repair or installation fails we come back at no charge.
DIY or Call Us?
Some checks are safe and useful for any owner: open the cabinet, read the spec label, measure the door and photograph the hinge plate. Those help you self-qualify before you call anyone. A simple hinge or drawer slide swap is within reach for a confident homeowner with the right matched part.
Where it goes wrong: cabinet box work, countertop section replacement, and anything involving a cut stone or engineered surface (Cambria and Silestone included) really does need a trained installer. Setting an engineered countertop section wrong can crack it, and a failed seam re-set can let water into the cabinet run. Backsplash re-set in tight quarters also goes sideways without the right adhesive and layout planning. None of this is dangerous like wiring or gas, but it is the kind of work where a small mistake costs you the whole part. If you’re unsure, call us at (844) 797-6157 and we’ll tell you honestly whether it’s a repair, a part swap, or nothing to worry about yet.
FAQs

Doors, drawer fronts, and quality hardware typically hold up well for a decade or more when the cabinet stays dry and stable. In Enterprise’s dry climate, expect visible finishes to last longer than the hidden hardware, which is why hinges and drawer slides are usually the first parts to need replacing.
Often yes. A pulled hinge or a loose drawer corner can usually be re-set or re-glued. A swollen cabinet panel or an opening countertop seam usually needs replacement, not repair. Call (844) 797-6157 for a free estimate and we’ll tell you which category you’re in before any work begins.
A door-front or drawer-front swap is usually a couple of hours for a set. Countertop sections and full cabinet installations take longer and depend on how much of the kitchen is involved. We give you a written scope and timeline before we start.
We match your spec label and measurements to the correct OEM part for visible surfaces, and to quality aftermarket equivalents for hidden hardware when that saves you money. We don’t carry parts on a truck or keep local stock, so sourcing is ordered to your exact model. Call (844) 797-6157 for a free estimate to get started.
Whether you’re dealing with a sagging door, a failing seam, or a full kitchen that’s ready for an update, we’re here to help you figure out exactly what’s needed and what it costs. Our technicians have up to 22 years of experience, and every crew member is identity-verified with a name and photo before the visit, arrives in a marked uniform, and shows a photo ID badge at the door under The Threshold Standard. You get a written price before any work starts and a 365-Day Done Right Promise, so if the work isn’t right within a year, we make it right at no cost. Call Mason Remodeling Enterprise at (844) 797-6157 to schedule your free estimate.
Written by the team at Mason Remodeling Enterprise, serving Enterprise and nearby areas.












