







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Jerith Kitchen Remodeling: The Enterprise Owner’s Guide
Jerith-compatible kitchen remodeling in Enterprise typically runs $14,000 – $45,000 installed, depending on whether you’re refreshing cabinets and a backsplash or opening up walls and rebuilding the layout. This page covers the parts side of that equation: matching the right components to your Jerith cabinet system, understanding what fails first, and knowing what a replacement really costs before anyone puts a number on paper.

Most Enterprise homeowners don’t set out to research Jerith parts. They notice a door that won’t close flush, a drawer that sags under the weight of cast iron, or a hinge that leaves a hairline gap at the top of a cabinet face. A few find soft spots at the base of a sink cabinet after a slow leak went unnoticed. One failing component leads to another, and eventually the question becomes whether to repair the cabinet run or remodel the whole kitchen. In a house built during the 1990s and early 2000s boom years in Enterprise, we see that question more than any other.
Key Takeaways
- Jerith cabinetry in Enterprise homes usually needs parts attention at 12 – 18 years, faster if the kitchen faces west-facing afternoon sun.
- Cabinet installation in Enterprise runs $4,000 – $13,000; countertops $2,000 – $6,500; backsplash $800 – $2,500.
- You always get a written price before any work starts – not a verbal estimate that grows later.
- Mason Remodeling Enterprise is an independent service provider and is not affiliated with Jerith.
Which Jerith Models This Applies To

Jerith cabinet lines have been sold through several regional channels over the years, and the part that actually fits your kitchen depends on the box construction and door series rather than the color finish. The paper label stapled inside the door or on the back panel of a base cabinet usually carries a model code and a run date. If that label is gone, measure the door height and width to the nearest 1/16 inch, note the overlay (how much of the cabinet face the door covers – typically 1/2 inch for standard overlay, 1-1/4 inch for full overlay), and measure the hinge cup bore. Those three numbers will identify the compatible replacement faster than a photo will.
Here’s where Enterprise kitchens get complicated: a lot of homes use a two-tone layout from a remodel that happened 10 – 15 years ago, meaning one cabinet run may be a different Jerith series than the island or pantry. The overlay can differ between adjacent cabinets, which means the door you’re replacing may not match its neighbor. We see this in the gated communities off Horizon Ridge and in the older single-story neighborhoods near downtown Enterprise. Before ordering anything, we confirm the overlay and bore on each cabinet we’re touching.
OEM Jerith parts are the clean answer when they’re still available for your series – the bore, the finish, and the face profile match without compromise. Once a series is discontinued, a quality aftermarket hinge or drawer glide can match the bore and overlay, but the finish tone may read slightly different under Enterprise’s hard afternoon light. We tell homeowners this upfront: if the door itself is failing cosmetically, a matching finish from a cabinet partner like KraftMaid or Wellborn may be a better path than hunting a discontinued Jerith door. The decision usually comes down to whether you’re replacing one part or refreshing the whole kitchen.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Jerith Kitchen Remodeling Is Failing
- Doors that won’t sit flush. A hinge plate that has lost tension or a stripped screw hole in soft particleboard is the usual cause. Once the hinge pulls loose, the door sags and the adjacent door starts rubbing.
- Drawer boxes that rack side to side. The glide has worn or the box corner joint has opened. In Enterprise’s dry air, glue joints in older drawer boxes dry out and separate faster than they would in a humid climate.
- Soft spots or dark staining at the cabinet base. A slow supply-line or disposal leak has soaked the toe-kick and side panel. The cabinet box itself may be compromised, and no amount of new doors will fix a rotting box.
- Delaminating or bubbling finish on the door face. Direct sun exposure through west-facing windows cooks the finish and causes it to lift at the edges. This is common in Enterprise kitchens that get full afternoon sun.
- A gap between countertop and cabinet, or loose backsplash tile. The cabinet run has shifted or the substrate under the counter has sagged, which pulls the tile away from the wall. Left alone, the counter cracks at the sink cutout.
Replacement Cost & What’s Included

For a kitchen remodel in Enterprise, the installed range is $14,000 – $45,000, and a smaller kitchen refresh comes in at $9,000 – $20,000. Broken down by scope:
- Cabinet installation: $4,000 – $13,000
- Countertop installation: $2,000 – $6,500
- Backsplash installation: $800 – $2,500
- Kitchen island installation: $3,000 – $10,000
What drives the range is the part you don’t see: whether the cabinet boxes are sound or need replacement, whether plumbing and electrical need to move, and the countertop material. We provide a written, line-item price before any work starts, so you see what the parts cost and what the labor costs, separately. That’s not a promotion – it’s how every project works. If the work isn’t right within 365 days of the completion date, we make it right at no cost, with the terms stated in writing, including what’s covered and what’s excluded.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely handle the diagnostics yourself: measure the door, check the hinge cup bore, tighten a loose screw, and confirm the cabinet box is dry. Replacing a single hinge or glide on a standard-overlay cabinet is within reach for a careful homeowner.
Where it goes sideways is the part that isn’t obvious. A drawer glide that doesn’t match the box depth will rack and break the box corner. A door swapped without confirming the bore will not close flush. And when the issue is a rotted cabinet base under a sink, the water damage is usually larger than the visible soft spot – cutting into it without checking for a supply-line leak wastes the new parts you just bought. If a cabinet box or counter substrate has shifted, that’s structural and belongs with a professional. Call (844) 797-6157 and we’ll tell you which category you’re in. A live person answers, around the clock.
FAQs

How long do Jerith cabinet parts last in Enterprise? Most Jerith hinges and drawer glides hold up 12 – 18 years in an Enterprise kitchen, shorter in rooms that get full west-facing afternoon sun. The finish on door faces is often the first thing to fail, and cabinet boxes last longer if no leak has soaked the base.
Can the part be repaired instead of replaced? Often yes. A single hinge, glide, or loose door can usually be repaired without touching the rest of the run, and that’s the first thing we check. If the cabinet box is soft or the counter substrate has sagged, repair won’t hold and replacement becomes the honest answer. Call (844) 797-6157 for an exact quote – estimates are free.
How long does a Jerith parts swap take? A single hinge or glide replacement takes under an hour. A full cabinet door run is a half-day to a full day of work, and a whole-kitchen cabinet and countertop replacement is quoted as a multi-day project with a written schedule. We give you the timeline in writing before any work starts.
How do you source the Jerith part? We identify your cabinet’s series from the label or from measurements, confirm the overlay and bore, and source the compatible part – OEM when it’s available, a matched quality equivalent when the series is discontinued. We don’t carry parts on a truck or stock them locally; the part is confirmed against your cabinet before it’s ordered, so you’re not waiting on a guess.
Mason Remodeling Enterprise works with cabinet lines including KraftMaid, and surfaces from Cambria and Silestone, alongside Jerith-compatible replacements. Every crew member is background-checked and identity-verified through The Threshold Standard, and you get their name and photo before the visit. We’re an independent service provider and not affiliated with Jerith.
Ready to price your Jerith kitchen project in Enterprise?
Call (844) 797-6157 for a free estimate. You’ll get a written, line-item price before any work starts, a crew member verified by name and photo before they reach your door, and the 365-Day Done Right Promise behind the work. Estimates are free, and a live person answers every call, day or night.
Written by the team at Mason Remodeling Enterprise, serving Enterprise and nearby areas.












