







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Unilock Windows & Doors: The Enterprise Owner’s Guide
We install and repair Unilock-compatible windows and doors throughout Enterprise, with most full window replacements landing between $4,500 and $15,000 and impact-rated units running $8,000 to $25,000 depending on count and glass package. A single failed sash, hinge set, or door roller is a much smaller job, and we can often diagnose it on the first visit. Most Enterprise owners don’t notice a Unilock window or door part has failed until something stops working: a sash that won’t latch, a door that drags on the threshold, a handle that spins without grabbing, or a seal that lets desert grit through on a windy afternoon. That’s usually the moment the phone comes out.

Which Unilock Models This Applies To

Unilock has built windows and doors in several series over the years, and the part you need depends on which one is in your wall. The fastest way to identify your unit is to open the operable sash or door and look at the etched or printed label along the top or side of the frame track, which usually lists the series name, a model number, and the glass date. If that label is gone, measure the visible glass width and height and the frame depth, then photograph the hinge or lock hardware close up. Enterprise homes built in the 1990s and 2000s often carry Unilock units from a couple of different series, so a side-by-side visual comparison of two windows can tell you whether they match.
For Unilock specifically, the OEM-versus-aftermarket call comes down to hardware that’s out of production versus hardware that still crosses over. Rollers, weatherstripping, and many hinge styles have quality aftermarket equivalents that fit correctly and cost less. Locking mechanisms, multi-point door hardware, and anything tied to the glass package are where we lean OEM or a verified substitute, because a mismatched lock can leave a door that closes but doesn’t secure. We’re an independent service provider and not affiliated with Unilock, so we source what actually fits your unit rather than what’s easiest to stock.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Unilock Windows & Doors Is Failing
- The sash won’t latch or lock. Usually a worn lock keeper or a frame that’s shifted slightly with seasonal movement. A latch that misses is also a security gap, not just a nuisance.
- The door drags or scrapes the threshold. In Enterprise, heat and dry air cause door slabs and frames to move more than most owners expect. Worn rollers or a settled hinge are the common culprits.
- You feel air or grit around the edges. Failed weatherstripping or a compressed seal lets desert dust in on windy days. This shows up as dust lines on the sill and higher cooling bills in summer.
- The handle spins or feels loose. Worn internal hardware in the lock or handle set. Left alone, it tends to fail completely at the worst moment.
- Condensation or fog between the panes. A broken seal in the insulated glass unit. Once the seal fails, the glass itself needs replacement rather than a hardware swap.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Enterprise, window replacement runs $4,500 to $15,000 and impact window installation runs $8,000 to $25,000, both installed and including disposal of the old units. Where you land in that range depends on how many openings, the glass package you choose, and whether the frame is reused or the whole unit is swapped. Smaller hardware jobs are priced separately and quoted line by line. We check and adjust the operating hardware on every install, and the work is covered by our written guarantee: 365 days from the completion date, with a free return visit at no charge if a repair or installation fails. You’ll see the price in writing before any work begins.
DIY or Call Us?
Some checks are safe and sensible. You can confirm the label and model number, measure the glass, tighten a visibly loose handle screw, and clean the tracks to see whether a sash or door frees up. Cylinder and lock work on an exterior door is where DIY usually goes wrong, because a mis-seated lock can leave a door that closes but won’t secure, and exterior door glazing carries real injury risk if the unit is heavy or the glass is damaged. Windows and doors aren’t the same hazard as high-tension garage springs, but a dropped sash or a broken glass unit can still hurt you. If the part is internal to the lock or the glass seal has failed, call us at (844) 797-6157 for a free estimate.
FAQs

How long should Unilock windows and doors last? A quality Unilock window’s frame and glass typically hold up 20 to 30 years, while hardware like rollers, hinges, and weatherstripping often needs attention sooner. In Enterprise’s heat and dry air, seals and weatherstripping tend to wear faster than in milder climates, so expect to replace those before the window itself. Call (844) 797-6157 for an exact quote on your units.
Can a failed part be repaired instead of replaced? Often, yes. Worn rollers, hinges, and weatherstripping can usually be swapped without replacing the whole window or door, which keeps the cost down. A fogged glass unit or a failed lock is a bigger repair, and we’ll tell you honestly which path makes sense. Call (844) 797-6157 to schedule a free estimate.
How long does a hardware or part swap take? A single hinge, roller, or weatherstrip job is usually a few hours, while a full window or door replacement depends on the count and the glass. We confirm the timeframe in your written price before any work starts. Reach us at (844) 797-6157 to get started.
How do you source the right part for my Unilock model? We start with the label and your measurements, then match the series and hardware, choosing OEM or a verified aftermarket equivalent based on what actually fits. For Unilock, that fit-first approach matters more than brand loyalty to a part that’s been discontinued. Call (844) 797-6157 and we’ll help you identify the right part.
Whether you’re weighing a full window replacement or just need one stubborn hinge fixed, give us a call at (844) 797-6157 for a free estimate. We also work with KraftMaid, Cambria, and Silestone products for other parts of your home, and every Enterprise job comes with a written price before work starts and our 365-Day Done Right Promise behind it.
Written by the team at Mason Remodeling Enterprise, serving Enterprise and nearby areas.












