







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Cover Fence Installation: The Enterprise Owner’s Guide
We install Cover-compatible fence systems in Enterprise, and most residential jobs land between $3,500 and $9,000 installed, depending on footage, height, and material. We don’t promise same-day installs on planned fence work – nobody does a full fence correctly in an afternoon – but we give you a written price before anything starts, and our technicians have up to 22 years of experience with these parts. Most Enterprise owners discover the problem the same way: a post starts leaning after a summer of ground movement, a gate sags and drags, or a panel rack looks wrong after a wind event. You notice it on a walk-around, not on a schedule. That’s usually when the questions start.

Which Cover Models This Applies To

Cover builds fence and gate hardware in several series lines, and the parts are not interchangeable across them. The compatibility gotcha most Enterprise owners hit: Cover’s latch and hinge hardware is sized for specific post and gate-frame dimensions, so a latch that fits a 2-inch gate frame won’t seat correctly on a 2.5-inch frame, even when the brand and finish look identical. Before you order anything, find the label or stamp on the existing post cap or gate bracket. If the label is gone, measure the post cross-section and the gate-frame width to the nearest sixteenth of an inch. Those two measurements plus the series name (usually stamped on the hardware body) tell you exactly which part you need.
The OEM-vs-aftermarket decision is real here. Cover OEM parts match the original finish and fit exactly, and they carry the manufacturer’s spec. Quality aftermarket equivalents cost less and often perform the same for standard residential footages, but pay attention to gate hardware: aftermarket latches sometimes skip the self-latching mechanism that Cover’s residential gates include. That matters in Nevada, where pool-adjacent fences and gates see specific safety expectations. We’ll tell you plainly which parts we’d trust for your Enterprise property and which we wouldn’t.
On the material side, we also source cabinetry and surfaces through KraftMaid, Cambria, and Silestone if your fence project turns into a broader exterior-and-interior plan. We’re an independent service provider – not affiliated with Cover – so every recommendation is about what fits your gates and posts, not a brand script.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Cover Fence Installation Is Failing
Enterprise’s climate does specific things to fencing. Summer ground expansion and contraction pull posts out of plumb. Wind events rack panels. Here’s what to watch for and what each symptom usually means:
- Posts leaning out of plumb. Sun-baked soil shrinks and relaxes with the monsoon cycle, and a post set in loose fill moves. A single leaning post often means the concrete footing has lost its hold, not that the post itself failed.
- A gate that sags or drags. Cover’s gate hardware carries the full gate weight through the hinges. When hinges wear or the latch striker shifts, the gate drops and starts catching on the ground. Sag is almost always a hardware or mounting issue, not a panel issue.
- Latch that no longer self-latches. Spring tension in the latch assembly weakens over time, or the striker plate moves out of alignment. This gets noticed fast in households with kids or pets because the gate stops staying shut on its own.
- Panel rack and loose fasteners. After a wind event, panels can twist out of square. Loose brackets and backing plates are the giveaway – fasteners back out under vibration and the panel loses its alignment.
- Surface corrosion on hardware. Enterprise’s dry climate hides corrosion until a rare wet season exposes it. Finish failure on hinges or latches lets moisture trap against the metal, and the part seizes or rusts through faster than the panels around it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed fence work in Enterprise runs $3,500 to $9,000 for a typical residential yard, and that range covers labor, materials, and disposal of the old fence. What pushes you toward the top: total footage, height (a 6-foot privacy run costs more than a 4-foot boundary line), gate count, and whether the existing footings have to be pulled and reset. A simple vinyl or aluminum boundary fence sits near the bottom. Multiple gates, decorative panels, or a full replacement with new footings pushes toward the upper end. If the job is gate-and-hardware repair rather than full replacement, tell us – that’s often a much smaller job, and we’ll say so.
You get the scope and parts in writing before anything starts: which Cover-compatible parts are going in, the footage, the labor, and the total. The work carries our 365-Day Done Right Promise – if something isn’t right within 365 days of completion, we come back and make it right at no charge.
DIY or Call Us?
Some checks are safe to do yourself. Measure your post and gate-frame dimensions. Look for the series stamp on the hardware. Tighten a visibly loose latch screw. Walk the line after a wind event and note which posts are out of plumb. What we don’t recommend is digging out and resetting a post footing yourself, or swapping gate hardware while a heavy gate is hanging – a racked gate under tension can swing or drop, and the hardware carries real weight. That’s the point where the wrong tool or a rushed reset puts you under a falling gate.
For a post reset, a full gate hardware swap, or a replacement run, call us. A live person answers at (844) 797-6157, day or night, and the estimate is free. We’ll tell you whether you need full replacement or just a repair.
FAQs

A properly installed residential fence with Cover-matched hardware runs 15 to 20 years for panels and posts, and gate hardware typically needs service or replacement in that window because hinges and latches take the daily load. Enterprise’s dry summers are kind to panels but hard on footings, so post stability is what usually shortens lifespan. Call (844) 797-6157 for an exact quote on your footage.
Often yes. A single leaning post, a sagging gate, or failed latch hardware can usually be repaired rather than replaced, and repair costs a fraction of a full run. We’ll inspect and tell you honestly whether repair or replacement makes better sense. Call (844) 797-6157 to schedule the inspection.
A gate hardware swap or single-post reset is typically a half-day to a full day. A full fence replacement for a standard residential yard runs several days depending on footage and whether new footings are needed. Because this is planned work, we schedule it properly and give you the timeline in writing. Call (844) 797-6157 for scheduling.
We match your existing Cover series and dimensions to the correct compatible hardware, then source it from manufacturer and vetted supplier channels, OEM or quality aftermarket per your property’s needs. We don’t claim to stock parts – we verify the fit first. Call (844) 797-6157 and have your post and gate-frame measurements handy.
Written by the team at Mason Remodeling Enterprise, serving Enterprise and nearby areas.












