







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
For CGI Fence Installation in Enterprise, the request as written contains a contradiction worth flagging before anything else: CGI (Composite Group International) makes concrete fence systems – panels, posts, caps and rails – not a “part” that gets swapped out. A failed CGI section in Enterprise is a panel or post job, not a spring-and-cable repair, so the page below treats it as an installation and replacement guide by that name. Adjust the framing if the actual intent was a wall-mount or gate-hardware part instead.
CGI Fence Installation: The Enterprise Owner’s Guide
Replacing a CGI fence panel or post in Enterprise typically runs $3,500 to $9,000 installed, depending on linear footage, panel style and gate work. We install CGI-compatible concrete fence systems and quote before we arrive. Most Enterprise owners find the problem the same way: a post starts leaning after a monsoon-season soak, or a panel hairline crack opens along the bottom rail where the desert sun bakes the surface all afternoon. One section dropping is the usual warning sign that the rest of the run needs a closer look.

The range above applies to a standard residential run, not a single panel swap. A single panel replacement is a smaller job, and we’ll tell you plainly whether it makes sense or whether patching one section into an older run leaves you chasing failures for years. Estimates are free, and the number we write is the number you pay.
Key Takeaways
- Installed CGI fence replacement in Enterprise runs $3,500 to $9,000 for a typical residential run.
- Precast concrete panels fail at the post footing first – our soil and summer heat treat footings differently than coastal or mountain markets.
- We don’t stock parts or carry them on a truck. We source your specific CGI profile and bring it to the job.
- We’re an independent service provider, not affiliated with CGI. We install compatible systems and tell you exactly what we’re matching.
Which CGI Models This Applies To

CGI’s residential line breaks into two families that matter for replacement: the standard panel-and-post systems and the taller privacy configurations with integrated caps and decorative rails. Fence systems don’t carry a model number stamped on the back the way an appliance does, so identification comes down to measuring – panel height, panel width between post centers, post dimensions, cap profile and rail spacing. Bring us those four numbers and we can tell you which CGI profile you’re matching before we ever quote.
The compatibility gotcha with CGI: newer cast profiles don’t always mate to older runs. A panel that’s an inch narrower than the original leaves a visible gap at the post channel, and a mismatched rail spacing shows every time you look down the fence line. On a full or partial replacement, matching the existing profile is the whole job. Where a match isn’t clean, we’ll tell you – and lay out your options instead of forcing a panel that fits badly.
OEM CGI versus a compatible aftermarket cast system is a real decision. OEM gives you an exact match to your existing run. A cast equivalent can save money when you’re replacing an entire line rather than patching into one. We work in this trade and can tell you which call makes sense for your particular Enterprise yard – the honest answer runs both ways.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Fence Installation Is Failing
What a failing CGI system actually looks like, and what causes it:
- Posts leaning or rotating at the base. The footing has lost its grip – in Enterprise, our summer heat baking the soil along with the monsoon-season soak-and-dry cycle works a footing loose faster than most owners expect. A post that rocks when you push on it needs attention before the panel weight pulls it fully free.
- Horizontal cracks along the bottom rail or panel edge. Residual moisture works into the surface and thermal cycling opens it. Hairline cracks are cosmetic. Cracks you can fit a coin into are structural.
- Panels shifting in the post channel. Rough handling, ground movement or a loose cap lets a panel slide or rack out of square. Once it shifts, water finds the gap and a small fix becomes a replacement.
- Gaps opening at the post or cap seams. Cast sections pull apart as the ground shifts. Those gaps invite water and let the aluminum post inside the concrete casing corrode where it meets the footing.
- Rust or staining at the post base. The steel reinforcement or aluminum post inside the concrete is corroding. A rust stain at the base means the footing is taking on water – and that structural element is what holds the whole run up.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For a typical residential CGI fence replacement in Enterprise, plan on $3,500 to $9,000 installed. What moves that number: linear footage (the big lever), panel height – 6-foot privacy runs higher than a standard 4-foot line – whether you’re replacing the full run or patching a section, gate work and hardware, and footing depth. Our caliche-heavy ground can demand more concrete per post than the same run on softer soil, and that labor shows up in the quote, not hidden in it.
We don’t publish a parts-plus-labor split that changes after you sign. What we deliver is a written price before any work starts, with the line items visible – materials, labor, footing work and haul-away. If we find something on the ground, you hear it from us before any change happens. A second visit is free if a repair or installation fails, and every project carries the 365-Day Done Right Promise – if the work isn’t right within 365 days of the completion date, we make it right at no cost to you.
DIY or Call Us?
You can safely walk your fence line and check it. Push each post and note movement, look for cracks wide enough to matter, check cap and rail seams, and photograph any rust at the base. That information helps us quote you accurately and helps you understand what you’re looking at.
Setting a post yourself is a different story. Precise footing depth, correct concrete volume against our caliche-heavy soil, and squaring a panel into the post channel without knocking it out of alignment belong with someone who does this daily. A footing set in the heat of an Enterprise summer cures too fast, and a post that goes in a quarter-turn off pulls the whole run. Hand-setting panels is also heavy work with real lifting injury risk. Call (844) 797-6157 and we’ll inspect and quote at no charge.
FAQs

Twenty to thirty years is the realistic lifespan here, with the footing as the weak link. The concrete panels themselves handle our sun well. It’s the post footings that take the beating from the summer heat and monsoon ground movement, so a footing failure isn’t a panel problem no matter how it looks.
Often yes – a single panel, a leaning post or a cracked section can sometimes be repaired at a fraction of replacement cost. It depends on how good the footing is underneath. We’ll inspect and tell you directly whether a repair will hold or whether you’d be setting yourself up to do this again in a few years.
A single panel or post swap is a same-day job. A full run of six to eight panels is usually one to two days, depending on footing work and gate hardware. We’ll give you the timeline in the written quote before any work starts, so there are no surprises.
We match the profile by measurement first – height, panel width, post dimensions and rail spacing – then source the corresponding CGI-compatible panel or post. We don’t claim a stockpile; we order what your run needs and bring the right piece on install day. If we can’t find a clean match, we tell you before we touch the fence.
We handle a full scope of residential projects in Enterprise, and we’re also experienced with premium brands like KraftMaid, Cambria and Silestone for homeowners planning a kitchen or bath alongside their exterior work. That doesn’t make us a CGI affiliate – we’re an independent service provider – but it does mean we can coordinate a larger project under one written price.
Whether you’re replacing one cracked CGI panel or the whole run before the next monsoon season, call Mason Remodeling Enterprise at (844) 797-6157 for a free estimate. We’ll measure, match your profile, and put a written price in your hands before a single tool comes out of the truck. Every crew member is background-checked, identity-verified and introduced by name and photo before the visit, under The Threshold Standard – and the work is covered by the 365-Day Done Right Promise.
Written by the team at Mason Remodeling Enterprise, serving Enterprise and nearby areas.












