







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Home Additions & ADU: The Enterprise Owner’s Guide
We install CGI-compatible home additions and ADU packages in Enterprise, and the honest number for a finished, permitted addition here runs $45,000 – $130,000 depending on square footage, foundation and whether you’re touching plumbing. Equipment-specific parts, like a replacement window unit, panel, or door hardware on a CGI-structured build, are usually sourced and swapped within days, not weeks. Most Enterprise owners first notice trouble the same way: a room that never heats evenly, a soft spot near a slider, a hairline crack above a header, or a door that suddenly won’t latch in July.

Those symptoms aren’t cosmetic. In a CGI-framed addition they almost always point to a failed component in the envelope or the structural tie-in, and the faster you match the right part to the right model, the less of the build you end up paying to redo.
Key Takeaways
- A finished addition in Enterprise: $45,000 – $130,000. An ADU: $90,000 – $220,000. A garage conversion: $30,000 – $80,000.
- Match parts to your CGI series by the data plate and stamped dimensions, not by eye.
- Nevada’s 100°F-plus summers and monsoon wind load both stress envelope components harder than a coastal climate does.
- Every job gets a written price before any work starts and a written guarantee covering 365 days from completion.
Which CGI Models This Applies To

CGI builds in Enterprise fall into a few families: single-story room additions, two-story and second-floor bump-outs tied into the existing roof line, and detached or attached ADU structures. Each family uses different tie-in hardware, header sizing and envelope details. The part you need is defined by your structural series and the load class stamped on the plans or the data plate, not by the year the build went up.
Here’s where owners get burned. Two CGI additions built the same year can carry different sill heights and different wind-load ratings, because Enterprise sits in a high-wind and high-heat zone and plans get amended on site. That’s the compatibility gotcha: the part that fits your neighbor’s CGI addition down the street often will not fit yours. Confirm the dimension and the load rating off the plate before you order anything.
The OEM versus aftermarket decision matters here too. CGI’s factory components give you an exact fit and a documented spec, which is what you want on load-bearing tie-ins or anything punched through the envelope. Quality aftermarket equivalents are fine for trim, hardware and non-structural parts, and they usually cost less. We source both.
Mason Remodeling Enterprise is an independent service provider and is not affiliated with CGI. We work with CGI-built homes, we don’t represent the manufacturer.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Home Additions & ADU Is Failing
Watch for these five, and note the cause under each. They tell you whether you’re facing a small part swap or something structural.
- A door or slider that won’t latch in summer. Wood and composite framing swell as temperatures climb past 100°F in Enterprise, and a failing threshold or header tie lets the frame move. That’s a settling component, not a sticky door.
- Hairline cracks radiating from a corner or above a header. The tie-in hardware is working loose from the existing structure. Small cracks near openings are usually a fixable part; cracks running across a whole wall mean the load path needs a look.
- Soft spots or water staining near a wall-floor junction. Envelope or flashing failure. Once water gets behind the finish, the framing underneath starts to go, and you want to catch this fast in a rainy season.
- A room that heats unevenly or a cold spot along one wall. An insulation or window unit has failed. You feel it before you see it, and it shows up on the power bill before either.
- Sun-faded, chalky, or cracked sealant at exterior joints. UV in Enterprise eats cheap sealants in two or three years. It’s the cheapest thing to fix and the most expensive thing to ignore.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s where Enterprise owners usually need a real number before they decide anything:
- Kitchen remodels inside an addition: $14,000 – $45,000
- Bathroom remodels inside an addition: $9,000 – $28,000
- Full home addition: $45,000 – $130,000
- ADU construction: $90,000 – $220,000
- Garage conversion: $30,000 – $80,000
What pushes you toward the top of a range: foundation work, plumbing or electrical relocation, roof tie-in complexity, and whether the part is structural or cosmetic. A load-bearing tie-in part costs more than trim hardware, full stop.

Every Mason Remodeling Enterprise project comes as a written, line-item price before a single tool comes out of the box. No verbal estimate. No change-orders that appear on the final bill. The work is covered by a written guarantee for 365 days from the completion date, and if a repair or installation fails in that window, we return at no charge.
DIY or Call Us?
You can safely check a lot of this yourself. Look at the data plate for the series and load rating, measure the part’s mounting points, photograph the joint or the failure, and note whether the issue is cosmetic or structural. That information is genuinely useful to have in hand when you call.
Where DIY goes wrong: load-bearing tie-ins, envelope penetrations, window unit swaps above the first floor, and anything involving the addition’s electrical or plumbing. A structural tie-in that isn’t torqued or matched to the right load class is a serious safety issue, not a weekend project. Window and panel work up high is dangerous for the same reason.
The safest thing you can do is let a trained professional handle the parts that keep the structure sound. Our technicians have up to 22 years of experience with CGI and similar builds, and they’ll bring the right part and the right torque the first time. Call (844) 797-6157 and we’ll set up a free estimate.
FAQs

Sealants and exterior joint hardware last two to five years in Enterprise’s UV and heat; structural tie-ins and framing components last decades when properly installed. The difference is almost always whether they were matched to the right load class and installed by someone who knew the model. Call (844) 797-6157 for a free estimate if you’re not sure what you’re looking at.
Sometimes yes, and we’ll tell you straight when a repair is the honest answer. Cosmetic and non-structural parts often can be repaired; load-bearing tie-ins and envelope components usually get replaced because a patch won’t hold the rating. Call (844) 797-6157 and we’ll look before we quote.
Non-structural parts swap same-day; structural tie-ins and envelope work take longer, generally one to three days depending on what’s involved. The written price you get up front includes the estimate for time, and a change to that estimate has to come from something we discover on site, not from the invoice showing up bigger than quoted. Call (844) 797-6157 for an exact scope.
We match on the series and load rating off your data plate, then source either the OEM component from CGI’s supply chain or a vetted aftermarket equivalent when the OEM isn’t the best fit for a non-structural part. You get the exact part specified in the written price before work begins, so you know what you’re paying for. Call (844) 797-6157 to start the identification.
We do. If your addition or ADU involves cabinetry or surfaces, we work with those brands alongside the structural work, so you can spec the whole project in one place. Call (844) 797-6157 and we’ll walk through it.
Ready to get the right part at a fair price, installed by a crew you can verify before they knock? We’ll give you the written price before any work starts, back the installation for 365 days, and answer the phone when you call. Call Mason Remodeling Enterprise at (844) 797-6157 for a free estimate.
Written by the team at Mason Remodeling Enterprise, serving Enterprise and nearby areas.












