







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Moen Bathroom Remodeling: The Enterprise Owner’s Guide
Bathroom remodeling in Enterprise with Moen fixtures typically costs $9,000 to $28,000 installed, depending on whether you’re replacing a shower valve and trim or rebuilding the whole room around it. We install Moen-compatible work on scheduled timelines, not same-day, because a proper remodel involves permits, waterproofing and inspection. A written price comes before work starts, and every job carries our 365-Day Done Right Promise.

Most Enterprise homeowners don’t arrive at this decision through a catalog. They arrive because something failed. A Moen single-handle shower valve that suddenly runs hot when someone flushes a toilet. A Posi-Temp cartridge that won’t hold temperature anymore. A tub spout diverter that sends half the water up the wall. Or a 1222 or 1225 cartridge that drips no matter how hard you tighten the handle. In a bathroom remodel, the fixture is often the reason the project starts, and Moen is the brand most Enterprise bathrooms are built around.
Which Moen Models This Applies To

Moen’s residential line is organized by valve family, and that family is what determines which parts fit and which trim kits are compatible. Getting this wrong is the single most common ordering error in Enterprise bathroom remodels.
The two families you’ll meet most often in Enterprise homes are Posi-Temp (pressure-balancing, single-handle showers, using the 1222 cartridge) and M-PACT (the newer system with a universal valve that accepts any M-PACT trim, including the Gibson, Genta and Doux collections). Older Moen tub-and-shower setups often run on the 1200/1225 cartridge series. If your home has a Moen Motionsense or ioDigital shower, the parts live inside a digital mixing module, not a mechanical cartridge, and a standard replacement won’t work.
How to Identify Your Moen Valve Before You Order
- Remove the handle and escutcheon (the decorative plate behind it) and look for a stamped model number on the cartridge retaining nut or valve body.
- Measure the cartridge length. A 1222 Posi-Temp cartridge and a 1200 series cartridge are not interchangeable, and they look similar at a glance.
- Photograph the valve body, the trim, and any stamped numbers. That photo set is what a supplier needs to match a part correctly.
- If the valve is behind tile and you can’t see the stamp, look for a Moen label inside the shower wall access panel or on the underside of the valve trim.
OEM versus aftermarket: For cartridges, we strongly favor genuine Moen OEM. Aftermarket cartridges for the 1222 and 1225 families are widely sold, but the rubber cups and brass tolerances are where the cost cuts show up. In a high-mineral-water market like Enterprise, a cheap cartridge can fail in 18 months where an OEM part lasts the 10 to 15 years the valve was designed for. For trim and handles, quality aftermarket is usually fine. Mason Remodeling Enterprise is an independent service provider and is not affiliated with Moen; we source Moen parts through professional plumbing supply channels, not from a truck or a stockroom, so every part is ordered to your exact valve model.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Moen Bathroom Remodeling Is Failing
These are the failure patterns we see most in Enterprise, and each one points to a specific part.
- The shower runs scalding when a toilet flushes. That’s a failed pressure-balancing spool inside the Posi-Temp cartridge. The valve is no longer compensating for pressure changes in the supply line.
- A steady drip from the tub spout or showerhead with the handle off. The cartridge’s rubber cups or ceramic disc have worn. This is the classic 1222 or 1225 failure, and it wastes water every hour it drips.
- The handle turns stiffly or feels gritty. Mineral scale has built up inside the cartridge and on the stem. Enterprise’s hard water accelerates this, and it’s often the first warning before a full failure.
- Water temperature drifts or won’t hold. The temperature limit stop or the balancing mechanism has worn out. This one is a genuine scald risk, especially in a home with kids or older adults.
- The diverter won’t switch from tub to shower, or leaks between the two. The diverter spout or the diverter inside the valve has failed. On older Moen tub spouts, the internal diverter gate is a common wear point.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what Moen-related bathroom work runs in Enterprise, with parts and labor together so you can self-qualify before you call.
| Project | Installed Price Range |
|---|---|
| Full bathroom remodel (Moen fixtures included) | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement | $3,000 – $8,500 |
| Bathroom vanity installation | $800 – $3,000 |
What moves the number: whether the valve body is replaced behind the wall or just the cartridge and trim; whether tile has to come out to access the valve; the trim finish you choose (brushed nickel and matte black run higher than chrome); and whether the project expands into waterproofing, a new shower pan, or a layout change. Parts are always itemized on the written price. The work is covered by the 365-Day Done Right Promise for 365 days from the completion date, and if a repair or installation fails we come back at no charge.
DIY or Call Us?
There’s an honest split here, and it starts with safety. Replacing a Moen cartridge or a tub spout is within reach for a careful homeowner, but anything that requires opening the wall, shutting off the main water supply, or working on the valve body itself is where DIY goes wrong. A cross-threaded cartridge, a valve body cracked by overtightening, or a shower that’s left running behind a wall you thought was sealed can turn a $40 part into a several-thousand-dollar water-damage repair. And a temperature-balancing valve that’s reinstalled wrong is a scald hazard.
What you can safely do: shut off the water, remove the handle and escutcheon, photograph the valve, and confirm the model. That’s diagnostic work and it’s valuable. What we’d rather do: match the exact part to your Moen valve and install it correctly the first time, with a written price and a name and photo before we arrive. Call (844) 797-6157 for a free estimate, and we’ll confirm the part and the price before any work begins.
FAQs

A genuine Moen cartridge typically lasts 10 to 15 years in normal use, but Enterprise’s hard, mineral-heavy water shortens that. We regularly see 1222 and 1225 cartridges fail in 6 to 10 years here, and homes on well water can go sooner. If your shower valve is original to a 1990s or 2000s build, it’s a candidate for replacement. Call (844) 797-6157 for an exact quote; estimates are free.
Sometimes. A cartridge that’s scaled but not worn can occasionally be cleaned and re-greased, and a handle that’s just stiff from mineral buildup may not need replacement at all. But once the rubber cups or ceramic disc are worn, replacement is the only real fix. We’ll tell you honestly which one your valve needs. Call (844) 797-6157.
A cartridge replacement is usually a 1 to 2 hour job once the water is off and the part is confirmed. If tile or wall has to be opened to reach the valve, or if the valve body itself needs replacement, plan on half a day or more. The trimming and sealing are done the same visit. Call (844) 797-6157 to schedule.
We order to your exact valve model from professional plumbing supply channels, using the model number or the photos you provide. Nothing comes off a truck or a shelf waiting to be guessed at. Mason Remodeling Enterprise is an independent provider, not affiliated with Moen, so we match the part to your valve rather than the other way around. For Kohler, KraftMaid, Cambria or Silestone work, we source those the same way. Call (844) 797-6157 for a free estimate.
If your Moen fixture has failed or your Enterprise bathroom is ready for a real remodel, the next step is a written price before any work starts. Call (844) 797-6157 to schedule your free estimate with Mason Remodeling Enterprise, and we’ll confirm the part, the timeline, and the price in writing.
Written by the team at Mason Remodeling Enterprise, serving Enterprise and nearby areas.












