







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Therma-Tru Kitchen Remodeling: The Enterprise Owner’s Guide
We install Therma-Tru-compatible kitchen remodeling for Enterprise homeowners, with a typical installed price of $14,000 – $45,000 depending on scope, and most jobs are planned on a scheduled timeline, not patched together same-day. Where Therma-Tru systems intersect with a kitchen remodel, the most common failure we see is a patio or garden door leading off the kitchen that no longer latches, seals, or swings true – a draft you feel at the breakfast table and a door that sticks on the jamb once summer heat settles in. Owners usually notice it as a soft seal gap at the bottom sweep, fogged glass in a door light, or a strike plate the deadbolt won’t line up with.

Which Therma-Tru Models This Applies To

Therma-Tru makes facing doors, entry doors, patio and garden doors, and door accessories, and each line uses different hinge patterns, sill geometry, and glass cartridge dimensions. The model plate is usually on the hinge jamb of the door – take a photo of it before you call anything in. If there’s no plate, measure the slab width, height, and thickness in three places; Therma-Tru slabs commonly fall into 1-3/4″, 1-3/8″, 80″, and 96″ size tiers, and getting one measurement wrong means the new unit will not hang.
On the OEM-versus-aftermarket question: Therma-Tru OEM parts carry a known fit for the model line but can be slow to arrive from the factory, and pricing is higher. Aftermarket equivalents for sweeps, sill caps, weatherstrip, and glass cartridges are widely available and often indistinguishable in service life; for a hinge, lock prep, or structural jamb component on an exterior door, we lean OEM because aftermarket tolerances wander. We have the technicians to know the difference by sight and will tell you which side of that line your part falls on before we quote it.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Therma-Tru Kitchen Remodeling Is Failing
- Door drags on the sill or strike won’t catch. Hinge screws have backed out of stressed jamb wood, or the header has shifted – common in Enterprise where slab-on-grade homes move with summer heat. Left alone, the frame warps and the door will not close at all.
- Fogged glass in the door light. The sealed insulated glass unit has lost its argon; moisture condensed inside the pane. No amount of wiping fixes it, and the glass must be replaced, not resealed.
- Daylight visible at the threshold or along the jamb. The sweep or weatherstrip has hardened and pulled away, letting hot desert air and dust through. This is one of the cheapest failures to catch early – it just needs the right strip profile to fit your sill.
- Bottom sweep hanging in shreds. UV and dry heat in southern Nevada age rubber and vinyl sweeps faster than in cooler climates; the sweep or sill cap wears through at the door’s pivot zone. A torn sweep also lets water in during monsoon storms.
- Lock set or deadbolt no longer lines up. Someone changed the strike or jamb and the door no longer throws true. A misaligned lock is a security failure, not just a cosmetic one, and needs the strike plate refit or the hinge jamb addressed.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For a door or glass component tied to your kitchen remodel in Enterprise, approach it as a full kitchen scope where the door is part of the job, not an add-on. Our published kitchen remodel range is $14,000 – $45,000, with the door’s part and installation labor folded in and itemized on the written price. A cabinet package for the same kitchen runs $4,000 – $13,000; countertops $2,000 – $6,500; and a small kitchen remodel $9,000 – $20,000 when the layout allows.
What drives the range inside the door scope: whether it’s a slab-only swap or a full frame-out with new jamb, the glass cartridge type, siding and trim repair around the opening, and whether the surrounding wall needs drywall patched back after removal. We give a written price before any work starts, itemize parts and labor, and cover the work with a written guarantee for 365 days from the completion date. That includes a free return visit at no charge if a repair or installation fails.
DIY or Call Us?
You can safely photograph the model plate, measure the slab and frame, wipe down the sweep to see whether the rubber is cracked or just dirty, and test the lock alignment. What goes wrong on exterior doors is the hidden side: removing a hinge jamb on a door set in stucco or siding risks cracking stucco and, if the opening wasn’t flashed correctly the first time, peeling back a water issue the size of the wall. Trying to force a warped frame or ream out a hinge to make a lock throw can open a gap that either fails a later inspection or lets water into the wall cavity.
On exterior-door components tied to your kitchen remodel, we treat the whole opening as structural – we pull the permits where the work requires them and inspect the sill and flashing before we close anything in. Call (844) 797-6157 for a free estimate and we’ll tell you which part you actually need and which side of the OEM-versus-aftermarket line it sits on. We’re an independent service provider, not affiliated with Therma-Tru.
FAQs

How long does a Therma-Tru door component last in Enterprise? Weatherstrip and sweeps typically go 5 – 8 years in southern Nevada’s dry heat, glass cartridges 10 – 15, and the structural door frame can outlast the house if the flashing was done right. Ours have the technicians to tell you which layer you’re looking at from the photos.
Can it be repaired instead of replaced? Often, yes. Sweeps, sill caps, weatherstrip, strike plates, and glass cartridges are all replaceable without pulling the whole door. Hinges and jamb components are worth refitting before replacing, but only if the frame isn’t warped. We’ll tell you honestly whether a repair is real or just delaying a replacement.
How long does the swap take? A sweep or weatherstrip swap is typically under two hours, a glass cartridge or hinge set half a day, and a full door swap is a full day if the opening and trim need rework. If permits are required, add the inspection window. We schedule around the rest of your kitchen timeline.
How do you source the part? We match the part to your model plate and measurements, order OEM where the tolerance matters and a vetted aftermarket equivalent where it does not, and confirm arrival before we schedule the visit. Call (844) 797-6157 for an exact quote – estimates are free.
Written by the team at Mason Remodeling Enterprise, serving Enterprise and nearby areas.












